Tier 5 Standard

ADM MILLING CO

📍 1120 KING STREET, CHATTANOOGA, TN 37403🏭 Flour Milling (NAICS 311211)📅 2003-05-01
$2,300.00
Total Penalties
3
Citations
1/100
Risk Score
383
Analysis Words
Enforcement Analysis

According to U.S. Department of Labor enforcement records, ADM MILLING CO — a flour milling facility located at 1120 KING STREET, CHATTANOOGA, TN 37403 — was the subject of a formal OSHA inspection that resulted in 3 citation(s) and cumulative proposed penalties of $2,300.00. The inspection case was opened on 2003-05-01.

DOL records document workplace safety violations warranting formal citation under the OSH Act. While classified at the standard enforcement level, all OSHA citations require corrective action and may indicate areas where workplace safety programs should be strengthened.

BLS Injury Data: According to the Bureau of Labor Statistics (2022), this industry sector has an occupational injury rate of 3.3 per 100 full-time workers — 22% above the national average of 2.7. The sector fatality rate is 2.3 per 100,000 workers.

Industry Benchmark: The total penalty of $2,300.00 is 73% below the national average of $8,527.19 for facilities in the Manufacturing sector (NAICS 311211). This sector encompasses 24,420 inspected facilities nationwide with aggregate penalties totaling $208.2M.

State Context: Within TN, this facility's penalty places it at the 82th percentile among 40,481 inspected facilities. The statewide average penalty is $1,620.08.

Citation Analysis: The inspection produced 3 citations spanning 3 distinct OSHA regulatory standards. The citation breakdown includes: 2 other-than-serious — The violation has a direct relationship to job safety and health but is unlikely to cause death or serious physical harm. 1 serious — A workplace hazard that could cause death or serious physical harm exists, and the employer knew or should have known about the condition.

Enforcement Timeline: Citations were issued beginning October 28, 1999 with the latest abatement deadline set for July 12, 2003. Of the 3 total citations, 3 (100%) have been marked as abated in DOL records, indicating substantial compliance with corrective action requirements.

Penalty Assessment: The total proposed penalty of $2,300.00 falls within OSHA's standard enforcement range and may have been adjusted through informal settlement conference procedures, penalty reduction factors, or good faith credit for demonstrated safety and health management systems.

Industry Benchmark (TN)

This facility's $2,300 penalty is higher than 57% of all penalized companies in the NAICS 311211 industry in TN. The state average penalty for this industry is $9,466.

$9,466
State Avg
$2,300
This Facility
Citation Matrix — 3 Citations
29 CFR 1910.23(c)(01)
Guarding Floor & Wall Openings
Other-than-Serious
Penalty: $100.00Gravity: nanIssued: October 28, 1999Abated: ✓ Yes
29 CFR 1910.151(c)
Medical Services & First Aid
Other-than-Serious
Penalty: $100.00Gravity: nanIssued: October 28, 1999Abated: ✓ Yes
29 CFR 1910.272(j)(02)
Serious
Penalty: $2,100.00Gravity: nanIssued: June 19, 2003Abated: ✓ Yes
This report is compiled from publicly available U.S. Department of Labor enforcement data under the Freedom of Information Act. SVEP Navigator is an independent research and analysis platform and is not affiliated with, endorsed by, or connected to OSHA, the Department of Labor, or any federal agency. Information is provided for research, educational, and compliance planning purposes only and does not constitute legal advice. Penalty amounts shown are proposed penalties and may have been modified through contest proceedings or settlement.
Local Competitor Benchmark

Comparing penalized facilities in CHATTANOOGA, TN (Exact Industry)

ADM MILLING CO (This Facility)
$2.3K
3 cit.
HORIZON MILLING LLC
$45.0K
4 cit.
ADM MILLING COMPANY
$2.3K
5 cit.
More TN Enforcement Records
KILGORE FLARES COMPANY LLC
TOONE, TN
$541.9K
70 cit.
HANKOOK TIRE MANUFACTURING TENNESSEE LP
CLARKSVILLE, TN
$282.5K
40 cit.
YAMAKAWA MANUFACTURING CORPORATION OF AMERICA
PORTLAND, TN
$217.6K
50 cit.
HANKOOK & COMPANY ES AMERICA CORP.
CLARKSVILLE, TN
$189.2K
45 cit.
VALERO REFINING COMPANY-TENNESSEE LLC
MEMPHIS, TN
$172.9K
58 cit.
Other Inspected Facilities in CHATTANOOGA, TN
MUELLER CO LLC
$160.5K
203 cit.
SHIMMICK CONSTRUCTION COMPANY, INC.
$68.3K
8 cit.
B E & K CONSTRUCTION CO
$53.0K
5 cit.
HORIZON MILLING LLC
$45.0K
4 cit.
JOE SLIGER DBA EASTMAN CONSTRUCTION
$44.8K
54 cit.
Related Guides & Tools
OSHA Fines & Penalties Guide →
How OSHA calculates penalties and maximum fine amounts.
Top 10 OSHA Violations →
The most frequently cited standards nationwide.
Manufacturing Safety Data →
Industry-wide violation stats and rankings.
Penalty Calculator →
Estimate fines by violation type, industry, and size.

Explore more: OSHA enforcement in CHATTANOOGA · Tennessee data · Search the database · Incident Rate Calculator

Frequently Asked Questions
What OSHA violations was ADM MILLING CO cited for?

ADM MILLING CO received 3 citation(s) covering 3 distinct OSHA standards. Total proposed penalties were $2,300.00. The inspection opened on 2003-05-01.

How much was ADM MILLING CO fined by OSHA?

OSHA proposed penalties of $2,300.00 against ADM MILLING CO in CHATTANOOGA, TN. Average per citation: $766.67.

Is ADM MILLING CO a safe workplace?

Based on enforcement records, ADM MILLING CO has a risk score of 1 out of 100. DOL records document workplace safety violations warranting formal citation under the OSH Act. While classified at the standard enforcement level, all OSHA citations require corrective action and may indicate areas where workplace safety programs should be strengthened.

How does this penalty compare to the industry average?

The average penalty for Flour Milling facilities is $8,527.19. This facility penalty of $2,300.00 is below the industry average.