Tier 5 Standard

JARDEN PLASTICS

📍 1303 S BATESVILLE RD, GREER, SC 29650🏭 Plastics Material and Resin Manufacturing (NAICS 325211)📅 2013-03-28
$8,925.00
Total Penalties
6
Citations
4/100
Risk Score
394
Analysis Words
Enforcement Analysis

According to U.S. Department of Labor enforcement records, JARDEN PLASTICS — a plastics material and resin manufacturing facility located at 1303 S BATESVILLE RD, GREER, SC 29650 — was the subject of a formal OSHA inspection that resulted in 6 citation(s) and cumulative proposed penalties of $8,925.00. The inspection case was opened on 2013-03-28.

DOL records document workplace safety violations warranting formal citation under the OSH Act. While classified at the standard enforcement level, all OSHA citations require corrective action and may indicate areas where workplace safety programs should be strengthened.

BLS Injury Data: According to the Bureau of Labor Statistics (2022), this industry sector has an occupational injury rate of 3.3 per 100 full-time workers — 22% above the national average of 2.7. The sector fatality rate is 2.3 per 100,000 workers.

EPA Environmental Record: The EPA shows no current violations for this facility. regulated under: Clean Water Act, RCRA Hazardous Waste. Source: EPA ECHO database.

Industry Benchmark: The total penalty of $8,925.00 is approximately in line with the national average of $8,414.32 for facilities in the Manufacturing sector (NAICS 325211). This sector encompasses 52,095 inspected facilities nationwide with aggregate penalties totaling $438.3M.

State Context: Within SC, this facility's penalty places it at the 98th percentile among 39,390 inspected facilities. The statewide average penalty is $977.57.

Citation Analysis: The inspection produced 6 citations spanning 3 distinct OSHA regulatory standards. The citation breakdown includes: 6 serious — A workplace hazard that could cause death or serious physical harm exists, and the employer knew or should have known about the condition.

Enforcement Timeline: Citations were issued beginning June 3, 2013 with the latest abatement deadline set for July 8, 2013. Of the 6 total citations, 1 (17%) have been marked as abated in DOL records, which may indicate ongoing compliance gaps requiring further regulatory attention.

Penalty Assessment: The total proposed penalty of $8,925.00 falls within OSHA's standard enforcement range and may have been adjusted through informal settlement conference procedures, penalty reduction factors, or good faith credit for demonstrated safety and health management systems.

Industry Benchmark (SC)

This facility's $8,925 penalty is higher than 76% of all penalized companies in the NAICS 325211 industry in SC. The state average penalty for this industry is $6,111.

$6,111
State Avg
$8,925
This Facility
Citation Matrix — 6 Citations
29 CFR 1910.305(b)(01)
Electrical — Wiring Methods & Components
Serious
Penalty: $0.00Gravity: 10Issued: June 3, 2013Abated: Pending
29 CFR 1910.215(b)(09)
Abrasive Wheel Machinery
Serious
Penalty: $300.00Gravity: 01Issued: June 3, 2013Abated: Pending
29 CFR 1910.305(b)(02)
Electrical — Wiring Methods & Components
Serious
Penalty: $2,750.00Gravity: 10Issued: June 3, 2013Abated: Pending
29 CFR 1910.305(b)(01)
Electrical — Wiring Methods & Components
Serious
Penalty: $2,750.00Gravity: 10Issued: June 3, 2013Abated: Pending
29 CFR 1910.333(a)
Serious
Penalty: $1,750.00Gravity: 10Issued: June 3, 2013Abated: ✓ Yes
29 CFR 1910.305(b)(02)
Electrical — Wiring Methods & Components
Serious
Penalty: $1,375.00Gravity: 10Issued: June 3, 2013Abated: Pending
This report is compiled from publicly available U.S. Department of Labor enforcement data under the Freedom of Information Act. SVEP Navigator is an independent research and analysis platform and is not affiliated with, endorsed by, or connected to OSHA, the Department of Labor, or any federal agency. Information is provided for research, educational, and compliance planning purposes only and does not constitute legal advice. Penalty amounts shown are proposed penalties and may have been modified through contest proceedings or settlement.
Local Competitor Benchmark

Comparing penalized facilities in GREER, SC (Broader Sector)

JARDEN PLASTICS (This Facility)
$8.9K
6 cit.
WURTH WOOD GROUP INC
$13.1K
10 cit.
76575 - CBS MARKETING SOLUTIONS INC
$11.9K
12 cit.
75727 - JADEX
$6.9K
7 cit.
More SC Enforcement Records
ALBRIGHT & WILSON AMERICAS, INC.
CHARLESTON, SC
$900.3K
43 cit.
FRIGIDAIRE HOME PRODUCTS
ORANGEBURG, SC
$447.1K
129 cit.
PHILIP SERVICES CORPORATION
CHARLESTON, SC
$270.6K
46 cit.
BEACH BUNGEE, INC.
NORTH MYRTLE BEACH, SC
$244.0K
6 cit.
CHARLESTON SHIPBUILDERS, INC.
CHARLESTON, SC
$200.9K
48 cit.
Other Inspected Facilities in GREER, SC
EXIDE CORPORATION
$73.8K
75 cit.
BMW MANUFACTURING COMPANY LLC
$47.5K
44 cit.
BULLDOG ERECTORS
$23.5K
8 cit.
75440 - INDUSTRIAL RECOVERY - RECYCLING INC
$19.1K
18 cit.
HOMELITE-TEXTRON
$13.9K
7 cit.
Related Guides & Tools
OSHA Fines & Penalties Guide →
How OSHA calculates penalties and maximum fine amounts.
After an OSHA Inspection →
Citations, appeals, and penalty negotiation steps.
Top 10 OSHA Violations →
The most frequently cited standards nationwide.
Manufacturing Safety Data →
Industry-wide violation stats and rankings.

Explore more: OSHA enforcement in GREER · South Carolina data · Search the database · Incident Rate Calculator

Frequently Asked Questions
What OSHA violations was JARDEN PLASTICS cited for?

JARDEN PLASTICS received 6 citation(s) covering 3 distinct OSHA standards. Total proposed penalties were $8,925.00. The inspection opened on 2013-03-28.

How much was JARDEN PLASTICS fined by OSHA?

OSHA proposed penalties of $8,925.00 against JARDEN PLASTICS in GREER, SC. Average per citation: $1,487.50.

Is JARDEN PLASTICS a safe workplace?

Based on enforcement records, JARDEN PLASTICS has a risk score of 4 out of 100. DOL records document workplace safety violations warranting formal citation under the OSH Act. While classified at the standard enforcement level, all OSHA citations require corrective action and may indicate areas where workplace safety programs should be strengthened.

How does this penalty compare to the industry average?

The average penalty for Plastics Material and Resin Manufacturing facilities is $8,414.32. This facility penalty of $8,925.00 is above the industry average.